Geotextile underlay material cost equals the area you purchase multiplied by the quoted price per m². Installed cost adds placement and any freight, testing, handling, or taxes not already included. For 200 m² of flat coverage, an assumed 10%–15% allowance gives a calculated fabric requirement of 220–230 m². At a quoted rate of P per m², that is 220P–230P for fabric before other charges, provided the supplier sells that quantity rather than whole rolls.
A reliable cash price requires a specified grade, order quantity, delivery destination, currency, and quotation date. No verified current market-price range is available for this article, so the calculations below are budgeting examples, not supplier offers. The 10%–15% allowance is an illustration, not an installation standard.
Which cost to compare
Separate the fabric rate from the installed rate and the whole lining-system budget. A low sheet-only price does not include the same work as a contractor’s installed price.
| Cost meaning | What it covers | When to use it |
|---|---|---|
| Underlay sheet price per m2 | Fabric only, no site work, on a stated ex-works or delivered basis, for a stated polymer, needle-punched nonwoven construction, mass per unit area, and test basis | Comparing fabric offers with identical specifications |
| Installed underlay cost per covered m2 | Purchased fabric plus any delivery not already included, placement, specified overlaps or seams, temporary ballast, and supervision, divided by net covered area | Budgeting the underlay work on site |
| Lined-area project cost including underlay | Installed underlay plus subgrade preparation, the geomembrane itself, drainage or cover layers where designed, engineering, testing, permits, and contingency | Approving the whole pond, reservoir, canal, or cell budget |
A delivered fabric quotation may already include freight. Check its named destination and exclusions before adding transport again. Overlaps and cutting losses increase purchased quantity; they should not also be added as a second fabric charge.
Why the underlay is separate
A geomembrane protection geotextile is a separate fabric layer beneath the membrane, intended to cushion it against contact with the supporting surface. An HDPE liner price does not automatically include that fabric. If the design also specifies protection above the membrane, measure and price that layer separately.
Geotextiles and geomembranes perform different jobs, so their square-metre rates are not interchangeable. The geotextile versus geomembrane comparison helps distinguish the two material lines in a quotation.
What changes the fabric price
Compare polymer, fibre construction, mass per unit area, required performance, roll dimensions, quantity, and delivery terms. GSM means grams per square metre: 500 g/m² contains 0.5 kg of fabric per m². ASTM D5261 covers measurement of geotextile mass per unit area. [1]
Jinseed identifies its nonwoven geotextile as needle-punched PET continuous-filament fabric. Equal GSM does not establish equal performance or equal price across different products. A continuous-filament and short-fibre comparison, or a woven and nonwoven comparison, should therefore use the specified test results as well as weight. These comparisons do not identify other fabric types as Jinseed products.
At the same material cost per kilogram, doubling GSM doubles the fabric mass per square metre. It does not establish a doubled selling price: processing, packing, minimum orders, and delivery terms also affect the quotation. Confirm roll gross weight and freight scope rather than inferring shipping cost from GSM alone.
Which grade to price
Price the grade in the approved design, not a default weight chosen solely for the application name. Protection, filtration, and reinforcement are distinct geosynthetic functions; a fabric suitable for one duty is not automatically suitable for another. [2]
For an aquaculture pond, a mining pad, or hydraulic engineering works, the substrate, loading, membrane, and layer arrangement must be considered together. CBR puncture and grab tensile are useful specification checks, but neither alone establishes protection performance under the actual site conditions. Selection and installation must be carried out by qualified personnel under the approved design and applicable local regulations.
Jinseed’s published protection and nonwoven product tables, checked on 13 November 2026, list the following values for matching 400–800 g/m² grades. These are published product values, not independently witnessed batch-test results. MD means machine direction.
| Fabric weight (ASTM D5261) | CBR puncture (ASTM D6241) | Thickness (ASTM D5199) | Grab tensile MD (ASTM D4632) | Tensile strength MD (data sheet) | Flow rate at 50 mm head (data sheet) |
|---|---|---|---|---|---|
| 400 g/m2 | 4,600 N | 3.0 mm | 2,050 N | 27 kN/m | 40 L/s/m2 |
| 500 g/m2 | 6,100 N | 3.9 mm | 2,500 N | 34 kN/m | 35 L/s/m2 |
| 600 g/m2 | 7,500 N | 4.4 mm | 3,000 N | 39 kN/m | 30 L/s/m2 |
| 700 g/m2 | 8,800 N | 4.8 mm | 3,400 N | 42 kN/m | 25 L/s/m2 |
| 800 g/m2 | 10,000 N | 5.2 mm | 3,800 N | 45 kN/m | 20 L/s/m2 |
The 800 g/m² row has twice the mass of the 400 g/m² row and about 2.2 times its listed CBR puncture force. That is not a price ratio or an allowable site load. Flow rate at a stated head is not the same quantity as permittivity. Ask for the current data sheet, reporting basis, and contractual acceptance values before treating two offers as equivalent.
Thickness also needs a test basis: ASTM D5199 measures nominal thickness, and the standard notes that applied normal load can affect the result. The listed millimetres should not be treated as the fabric’s thickness under every field load. [3]
How much fabric to buy
Measure the actual surfaces to be covered, including slopes and specified edge details, rather than using only a pond’s plan area. Add the fabric consumed by the approved overlap or seam layout, cuts, and penetrations. The geotextile cushion installation guide discusses placement details; the project specification controls their dimensions.
The table below shows only the arithmetic effect of assumed 10% and 15% allowances on flat areas. It excludes slopes, trenches, penetrations, and rounding up to saleable roll quantities. Neither percentage is a recommended allowance for every project.
| Net covered area | Calculated requirement at +10% | Calculated requirement at +15% |
|---|---|---|
| 100 m2 | 110 m2 | 115 m2 |
| 200 m2 | 220 m2 | 230 m2 |
| 500 m2 | 550 m2 | 575 m2 |
| 1,000 m2 | 1,100 m2 | 1,150 m2 |
Roll size can change the amount you pay. Jinseed’s protection page lists a 500 g/m² example roll measuring 6 m × 48 m: 288 m² of fabric and approximately 144 kg before core and wrapping. If a 200 m² job has a calculated requirement of 220–230 m² but the supplier sells only that whole roll, the purchase is 288 m², assuming the panel layout can be cut from it. At rate P, the fabric bill becomes 288P, or 1.44P per net covered m², before other charges. Confirm cut-length availability and minimum orders instead of assuming the calculated requirement is the invoiced quantity.
This published-roll calculation exposes a practical difference between coverage and purchasing: 288 − 230 = 58 m² and 288 − 220 = 68 m². That balance is material outside the example’s calculated requirement, not necessarily unusable waste. A cutting plan determines whether it can serve edges, patches, or another approved area. Use the supplier’s confirmed gross weight to plan unloading and storage; 144 kg is the calculated fabric mass, not the shipping weight.
Which extra costs to include
Ask who pays for each item below and whether it belongs in the underlay package or a separate site-work package. Allocate it once rather than adding it to both.
| Often-missed item | What to check in the quotation |
|---|---|
| Subgrade trimming and cleaning | Crews remove sharp stones and rubbish, repair soft spots, and dewater the formation before unrolling, which consumes labour and plant time |
| Overlaps, seams, and edge details | Specified overlap widths, sewn seams, anchor-trench embedment, and patches around penetrations consume fabric and sewing time |
| Placement and ballast | Crews unroll, position, and cut the sheet, weight it against wind, and guard it while the membrane team follows |
| Care during membrane installation | Crews keep equipment off the fabric, repair folds or damage, and coordinate the sequence between the two teams |
| Sampling, testing, and records | Staff check roll labels, draw conformance samples, inspect seams or overlaps, and compile as-built records where the specification requires them |
| Freight, handling, and taxes | Check delivery, unloading, storage, packing, minimum-order charges, duties, and taxes; add only items excluded from the quoted rate |
If the design uses LLDPE liner or textured liner, price the specified membrane and protection fabric together as separate lines. Settlement or a sloping surface alone does not establish the correct membrane or underlay grade.
For a landfill liner system, distinguish underlay cost from the whole cell budget. U.S. EPA describes composite liners and leachate collection as elements of municipal solid waste landfill containment requirements. [4] Its geosynthetic clay liner fact sheet also distinguishes geotextiles from the less permeable geomembrane. [5]
Closure, post-closure care, and financial assurance are broader U.S. landfill obligations, not components of a fabric-only rate. Requirements for a particular site depend on its jurisdiction and permit. [6]
How to obtain comparable quotes
Send each bidder the same information:
- Layer position and function, including any separate protection above the membrane.
- Polymer, fibre construction, GSM, and required performance values with test methods and acceptance basis.
- Drawings showing covered surfaces, slopes, edges, and penetrations, plus the panel or quantity take-off where available.
- Required roll sizes or cut lengths, total quantity, and any acceptable alternatives.
- Delivery destination, unloading arrangements, required date, currency, and quotation validity.
- A breakdown of fabric, freight, installation, testing, duties, and taxes, identifying every exclusion.
For CBR puncture comparisons, ASTM D6241 uses a 50 mm probe and describes the result as an index test suitable for commercial-shipment acceptance testing. It is not a project-specific membrane protection test. [7] The nonwoven data-sheet guide helps identify the different reported properties.
Jinseed’s company information and quality-control information describe its manufacturing and inspection arrangements. Ask for documents applicable to the quoted grade and shipment; company-level statements do not replace batch acceptance evidence. For a project quotation, provide the specification and quantity take-off at https://jinseed-geo.com/contact-us/.
Need an exact underlay price for your drawings?
Send Jinseed the grade or tender sheet, total underlay area, and delivery port. Ask for the available roll sizes, minimum order, delivery scope, and quotation validity.
References
- ASTM D5261-10(2024): Measuring Mass per Unit Area of Geotextiles.
- International Geosynthetics Society: Geosynthetics Functions.
- ASTM D5199-12(2019): Measuring the Nominal Thickness of Geosynthetics.
- U.S. EPA: Municipal Solid Waste Landfills.
- U.S. EPA: Geosynthetic Clay Liners Used in Municipal Solid Waste Landfills.
- U.S. EPA: Requirements for Municipal Solid Waste Landfills.
- ASTM D6241-22a: Measuring Static Puncture Strength Using a 50 mm Probe.